Zinsser Perma White - Mildew Proof Interior Paint - Semi Gloss
William Zinsser & Company Inc.
Perma White - Mildew Proof Bathroom Paint
GENERIC TYPESingle component water-borne acrylic topcoat.
GENERAL PROPERTIES
A durable, high peformance, semi-gloss acrylic topcoat for use in humid areas which are prone to mildew growth.
- Guaranteed mildew-proof finish
- Dries fast, recoat in 2 hours
- Self-priming, adheres to all surfaces
- Tintable to any pastel or medium shade
- Excellent flexibility and water resistance
- Will not peel or blister
- Easily applied by brush, roller, pad, or spray
- Meets the most stringent VOC (Volatile Organic Content) regulations in all states
As a self priming topcoat for interior industrial, architectural or home applications requiring a fast-drying water-based mildew-proof finish.
NOT RECOMMENDED FOR
Any exterior application or areas subject to prolonged water immersion such as bathtub or shower interiors, saunas or steamrooms.
SUBSTRATES
Apply over suitably prepared wood, drywall, plaster, masonry, metal, vinyl, glass, existing paint, wallcoverings or other surfaces as recommended. No extra primer required.
Specification Data
THEORETICAL SOLIDS CONTENT:| By Volume | By Weight | |
| Perma White | 38.6 percent | 52.1 percent |
VOLATILE ORGANIC CONTENT:
| lbs/gal | g/litre | |
| As applied | 1.34 | 160 |
THEORETICAL COVERAGE PER GALLON
698 sq. ft./gallon @ 1.0 mil (17.0 sq.m/l at 25 microns) dry film thickness.
Application losses will vary according to the porosity of the substrate and must be taken into consideration when estimating job requirements.
| WEIGHT PER GALLON | 10.5 to 10.8 lbs |
| VISCOSITY | 2,500-4,000 centipoise |
| DRY TIME TO RECOAT | 2 hours at 70°F |
| TIME TO FULL CURE | 7 days at 70°F |
| 60° GLOSS | 45-50 percent (SEMI-GLOSS) |
| COLOUR | White |
| FLASH POINT (Setaflash) | >200°F |
| FLAME SPREAD INDEX | 0 |
| FUEL DEVELOPMENT | 0 |
| SMOKE DEVELOPMENT | 5 |
| SHELF LIFE | Sixty months when stored at 75°F (24°C) |
| STORAGE CONDITIONS | Store Indoors Temperature: 40-100°F(4-43°C) Humidity: 0-95 percent Perma White is freeze/thaw stable |
PACKAGING
5 Gal. (19 L.), 1 Gal (3.8 L), 1 Qt. (0.95L)
APPLICATION INSTRUCTIONS
SURFACE PREPARATIONSurface must be clean and free of dirt, scaling paint, loose wallpaper or wallpaper paste. Test all old painted or varnished surfaces for adhesion by making an X with a razor or knife and placing a section of Scotch tape over, pressing down with thumb. After 30 seconds yank the tape off (do not pull but yank the tape). If the old paint or varnish comes off on the tape, the paint must be removed. Never paint over any painted surface that fails this test.
Fill cracks and nail holes with Ready Patch spackling compound; sand smooth when dry. Sand all new wood with fine sandpaper and remove dust. Remove oil, grease or wax with mineral spirits. Clean painted areas with a solution of 2 cups of household ammonia per gallon of water and rinse well. Remove existing mildew with household bleach instead of ammonia. Perma White is not designed to kill existing mildew but will prevent future growth on the paint film if properly applied (2 coats). NOTE: Never mix bleach with ammonia. It may cause death.
TINTING
May be tinted with most "universal" tinting colors up to 6 fluid ounces per gallon.
THINNING
Perma White is designed to be used as is. If thinning is necessary, use only water and no more than 10 percent by volume.
APPLICATION
Perma White is designed to be applied in 2 coats for maximum durability. The first coat primes and seals the surface and provides a base for the topcoat. The topcoat completes the sealing process while providing mildew protection and scrub resistance. NOTE: Covering Perma White with any other topcoat will ruin the finish's mildew-proof properties.
APPLICATION CONDITIONS
| Material | Surfaces | Ambient | Humidity | |
| Normal | 60-90°F | 65-85°F | 65-90°F | 10-80 Percent |
| Minimum | 45°F | 50°F | 50°F | 0 Percent |
| Maximum | 105°F | 130°F | 110°F | 85 Percent |
APPLICATION METHODS
Conventional Air SprayPressure pot equipped with dual regulators, 3/8 inch ID. minimum material hose, 0.086 inch I.D. fluid tip and appropriate air cap. Thin material with 10 percent water, spray at 30-40 psi.
Airless Spray:
| Pump Ratio | 30:1 (mm.) |
| GPM Output | 3.0 (mm.) |
| Material Hose | 3/8" l.D. (mm.) |
| Tip Size | 0.015"- 0.017" |
| Output psi | 2000 - 2500 |
| Filter Size | 60 |
Brush or Roller
Use clean, synthetic bristle brush. Flow product on and brush out. For rolling use a short nap roller.
DRYING TIME
Perma White will be dry and ready to recoat in 2 hours. Apply second coat 2 hours or longer after first. Low temperature, high humidity and poor ventilation will increase drying time. If used above shower walls, wait at least 24 hours before using shower. Do not scrub the new coating for seven days.
CLEANING EQUIPMENT
Brushes and rollers should be cleaned immediately after use with soap and water. Spray equipment should be flushed with water followed by mineral spirits. Wipe up spatters before they dry. If Perma White dries before you can cleanup, use a heavy-duty ammoniated household cleaner and rinse with water.
CAUTION: READ AND FOLLOW ALL CAUTION STATE-MENTS ON THIS TECHNICAL DATA SHEET AND ON THE MATERIAL SAFETY DATA SHEET FOR THIS PRODUCT.
SSL 
